Home - Education Resources - NDT Course Material - Ultrasound

Introduction to Ultrasonic Testing

Basic Principles
Present State
Future Direction

Physics of Ultrasound
Wave Propagation
Modes of Sound Waves
Properties of Plane Waves
Wavelength/Flaw Detection
Elastic Properties of Solids

Acoustic Impedance
Refraction & Snell's Law
Mode Conversion
Signal-to-noise Ratio
Wave Interference

Equipment & Transducers
Piezoelectric Transducers
Characteristics of PT
Radiated Fields
Transducer Beam Spread
Transducer Types
Transducer Testing I
Transducer Testing II
Transducer Modeling
Tone Burst Generators
Function Generators
Impedance Matching
Data Presentation
Error Analysis

Measurement Techniques
Normal Beam Inspection
Angle Beams I
Angle Beams II
Crack Tip Diffraction
Automated Scanning
Velocity Measurements
Measuring Attenuation
Spread Spectrum
Signal Processing
Flaw Reconstruction

Calibration Methods
Calibration Methods
DAC Curves
Curvature Correction
Thompson-Gray Model
Grain Noise Modeling

Selected Applications
Rail Inspection

Reference Material
UT Material Properties


Signal-to-Noise Ratio

In a previous page, the effect that frequency and wavelength have on flaw detectability was discussed. However, the detection of a defect involves many factors other than the relationship of wavelength and flaw size. For example, the amount of sound that reflects from a defect is also dependent on the acoustic impedance mismatch between the flaw and the surrounding material. A void is generally a better reflector than a metallic inclusion because the impedance mismatch is greater between air and metal than between two metals.

Often, the surrounding material has competing reflections. Microstructure grains in metals and the aggregate of concrete are a couple of examples. A good measure of detectability of a flaw is its signal-to-noise ratio (S/N). The signal-to-noise ratio is a measure of how the signal from the defect compares to other background reflections (categorized as "noise"). A signal-to-noise ratio of 3 to 1 is often required as a minimum. The absolute noise level and the absolute strength of an echo from a "small" defect depends on a number of factors, which include:

  • The probe size and focal properties.
  • The probe frequency, bandwidth and efficiency.
  • The inspection path and distance (water and/or solid).
  • The interface (surface curvature and roughness).
  • The flaw location with respect to the incident beam.
  • The inherent noisiness of the metal microstructure.
  • The inherent reflectivity of the flaw, which is dependent on its acoustic impedance, size, shape, and orientation.
  • Cracks and volumetric defects can reflect ultrasonic waves quite differently. Many cracks are "invisible" from one direction and strong reflectors from another.
  • Multifaceted flaws will tend to scatter sound away from the transducer.

The following formula relates some of the variables affecting the signal-to-noise ratio (S/N) of a defect:

Rather than go into the details of this formulation, a few fundamental relationships can be pointed out. The signal-to-noise ratio (S/N), and therefore, the detectability of a defect:

  • Increases with increasing flaw size (scattering amplitude). The detectability of a defect is directly proportional to its size.
  • Increases with a more focused beam. In other words, flaw detectability is inversely proportional to the transducer beam width.
  • Increases with decreasing pulse width (delta-t). In other words, flaw detectability is inversely proportional to the duration of the pulse produced by an ultrasonic transducer. The shorter the pulse (often higher frequency), the better the detection of the defect. Shorter pulses correspond to broader bandwidth frequency response. See the figure below showing the waveform of a transducer and its corresponding frequency spectrum.
  • Decreases in materials with high density and/or a high ultrasonic velocity. The signal-to-noise ratio (S/N) is inversely proportional to material density and acoustic velocity.
  • Generally increases with frequency. However, in some materials, such as titanium alloys, both the "Aflaw" and the "Figure of Merit (FOM)" terms in the equation change at about the same rate with changing frequency. So, in some cases, the signal-to-noise ratio (S/N) can be somewhat independent of frequency.